Ships from Shenzhen · DHL / FedEx / UPS worldwide

LIGHTSPEED

Samsung Charging Port Replacement: Sub-Board Swap Guide

17 November 2026 · LightspeedTools team

Short answer: On most Galaxy phones a Samsung charging port replacement means swapping the charging sub-board or port flex, not soldering a new connector. Open the phone (usually through the back), disconnect the battery, unplug the main flex, swap the board, move any separate mic or rubber parts across, and test charging, data, mic and fast charge before you reseal. Only when the port is soldered, or a new board does not help, do you move to hot air and the USB charge IC.

This guide covers the hands-on replacement only. If you have not yet confirmed that the port is the fault, rather than the battery, the cable or the board, start with our Samsung not charging diagnosis and come back here once the sub-board is the likely culprit.

Step 1: identify the exact part

Samsung uses several layouts for the USB-C port, and the right part depends on the full model number, not just the marketing name. Check Settings > About phone or the label in the SIM tray area for the SM- code. Regional variants of the same phone can use different boards: for example the Note 10 is listed both as the Note 10 SM-N970F USB charging port flex and the Note 10 SM-N970U USB charging port flex, and the two are not guaranteed to be interchangeable. Match the suffix (F, B, U, N and so on) before you order.

LayoutWhere you usually see itWhat you replace
Sub-board (small PCB) joined to the main board by a main flexMany Galaxy A models and several S and Note modelsThe whole sub-board, often with mic and sometimes headphone jack on it
Port on a flex or small board under the loudspeakerMany S and Note models, such as the S10, S20 and Note 10 familiesThe charging port flex or USB charging board for that variant
Port soldered to a boardSome models, and the connector on most sub-boardsThe bare USB-C connector, fitted with hot air

Layouts change between generations, so always compare the old part with the new one before fitting.

Tools you need

  • A heating pad or heat gun at controlled temperature for back glass adhesive. Our heating pads give even heat with less risk to the glass than a hot spot from a gun.
  • Suction cup, thin opening picks and a plastic spudger.
  • Phillips 00 screwdriver (some models use a slightly different size, so check before you strip a screw).
  • ESD mat and wrist strap, tweezers, isopropyl alcohol of high purity.
  • Replacement back adhesive or a pre-cut gasket for the model.
  • A USB tester for the final check. See our USB testers.
  • For soldered ports: hot air station, flux, low-temperature solder or solder paste, and a microscope.

Step 2: open the phone

Most Galaxy S and Note models from the last several generations, and many mid-range A models with glass backs, are opened through the back. Budget A models often have a plastic back that is clipped and lightly glued, so it needs less heat. A few models are serviced through the front with the display removed; on those, the screen is the part at risk, so confirm the access route for your model before you start.

  1. Power off the phone and remove the SIM tray.
  2. Heat the back evenly until the adhesive softens. Keep the glass warm, not hot to the touch for a long time; too much heat can damage the battery and the display.
  3. Lift one edge with a suction cup, slide in a pick and work around the edge slowly. Keep picks shallow near the camera and near the wireless charging coil.
  4. Remove the screws holding the top cover (wireless charging/NFC coil) and the bottom loudspeaker module. Note screw lengths; a long screw in the wrong hole can damage the display from behind.

Cracked back glass sheds shards. Cover it with packing tape before you heat and pry, and wear eye protection.

Step 3: disconnect the battery

Disconnect the battery connector before you touch any other flex. Lift it straight up with a plastic spudger, never metal, and fold it away so it cannot spring back. A live board can short and turn a port job into a board repair. Never pry against the battery; a punctured lithium cell can catch fire. If the battery is swollen, stop and replace it first.

Step 4: unplug and route the main flex

The sub-board connects to the main board through a long main flex (often called the FRC or interconnect flex) that runs alongside the battery. On many models it is lightly glued down.

  • Unplug both ends: one at the main board, one at the sub-board.
  • Lift the flex gently with a little heat or alcohol if it is glued. Do not crease it; a damaged main flex causes the same symptoms as a bad port.
  • Unplug the antenna coax cables that run to the sub-board area and note their routing. Swapped or loose antenna cables cause poor signal after the repair.
  • Unplug the display flex if it crosses or connects near the sub-board on your model.

If the old main flex shows tears, burns or corrosion on its connectors, replace it at the same time. A new board on a damaged flex will not fix anything.

Step 5: swap the sub-board or port flex

  1. Remove the screws holding the sub-board, then lift it from the side away from the USB-C opening. Some boards are lightly glued; a few drops of alcohol help.
  2. Compare old and new side by side: connector, flex sockets, mic hole, spring contacts and screw holes.
  3. Transfer separate parts. Depending on the model this can include the mic rubber boot or mesh, foam pads, the headphone jack seal, the vibration motor (on models where it is not fixed to the board), and grounding tape. Missing a mic boot is the most common cause of a quiet or echoing mic after the job.
  4. Seat the new board, check that the USB-C opening lines up with the frame, and refit its screws.
  5. Reconnect the main flex, antenna cables and display flex. Press each connector straight down until it clicks; never press at an angle.

Typical parts we stock for these layouts include the Note 10 Plus USB charging board, the S20 Ultra SM-G988B USB charging board and the Note 20 Ultra USB charging flex. Check the model code on each listing against the phone.

Step 6: test before you close

Reconnect the battery last and test with the back still off. If anything fails, you only have to unplug a connector, not cut fresh adhesive.

TestHowWhat a pass looks like
ChargingKnown good cable and charger, USB tester inlineCharging icon, steady current that rises after the phone negotiates
Fast chargeSamsung-compatible fast chargerPhone shows fast charging or super fast charging, tester shows a higher voltage or current step
Both cable directionsFlip the USB-C plugSame result both ways
DataConnect to a computerFile transfer prompt appears and files copy
MicVoice recorder and a test callClear audio, no hiss or echo
SignalCheck bars and make a callSame signal as before the repair
Moisture warningPlug in for a few minutesNo moisture detected warning

Our guide to USB tester readings explains what normal and abnormal numbers look like.

Step 7: reseal the phone

  • Disconnect the battery again, refit the loudspeaker module and the wireless charging/NFC cover, then reconnect the battery.
  • Remove all old adhesive from the frame and glass, clean with alcohol and let it dry fully.
  • Fit a fresh pre-cut gasket, lay the back on, and clamp or press it evenly for the time the adhesive maker recommends.
  • Tell the customer the original water resistance rating cannot be guaranteed after the phone is opened.

When the port is soldered: hot air and the charge IC

If the connector itself is damaged and only a bare port is available, or the board is not sold separately, you replace the port with hot air. Examples include the Galaxy S10 USB charging port and the Note 10 / S20 series USB charging port.

  1. Remove the board from the phone. Never apply hot air with the battery attached.
  2. Shield nearby plastic parts and connectors with heat-resistant tape.
  3. Add flux, preheat the board if you can, and heat the port evenly until all pins and shell legs release. Lift straight up.
  4. Clean the pads with flux and wick. Check under a microscope for lifted pads or bridged pins.
  5. Tin the pads lightly, place the new port, and reflow until it settles. Check every pin and the shell legs; a weak shell joint lets the port rock and fail again.

A low-temperature board preheater makes this safer on multi-layer boards; see our PCB preheater guide.

If a new port or board still gives no charging, or the phone charges but runs hot near the bottom of the main board, the USB charge IC may be at fault. This is a main board repair for experienced micro-solderers. We list parts such as the Note 10 USB charge IC 872C and the S10 big and small USB charging ICs. Confirm the IC position and marking against a schematic or board view for your exact variant before removing anything, and measure for shorts on the charging line first.

Common mistakes

  • Ordering by model name instead of the full SM- code and region.
  • Leaving the battery connected while unplugging the main flex.
  • Forgetting to move the mic boot or foam, giving weak call audio.
  • Swapping antenna cables, giving poor signal.
  • Closing the phone before testing charging, data and fast charge.
  • Replacing the port when the real fault is lint packed in the socket. Clean and inspect first.

Questions

Is the Samsung charging port part of the sub-board?

On many Galaxy models, yes: the USB-C connector sits on a small sub-board or flex at the bottom of the phone, joined to the main board by a main flex. Swapping that board replaces the port. On some models the port is soldered and needs hot air instead.

Do I need to remove the screen to replace a Samsung charging port?

On most Galaxy S, Note and many A models you go in through the back and the screen stays in place. A few models are serviced from the front, so check the access route for your exact model before you start.

Why does fast charging not work after a port replacement?

Check the charger and cable first, then the fit of the main flex at both ends. Some low-quality boards lack the parts needed for fast charge negotiation. If a known good board still will not fast charge, the fault may be on the main board.

Will my Samsung still be water resistant after the repair?

Not guaranteed. A fresh pre-cut adhesive and correctly seated seals help, but once the phone is opened the factory rating cannot be promised. Tell the customer before the job.

Find charging boards, port flexes and charge ICs by model on our Samsung parts page. Shops buying regularly can unlock trade prices through wholesale, and repeat orders by SKU or CSV are quickest through Quick Order.

Products in this article

More guides for repair shops